(!) Since support from Microsoft will end on January 14th, 2020, Windows 7 will be excluded from the recommended environment from December 15th, 2019 on this site. Vì lý do Microsoft kết thúc hỗ trợ cho Windows 7 vào ngày 14/01/2020, Windows 7 sẽ là hệ điều hành không được khuyến khích sử dụng với trang web này từ ngày 15/12/2019.
Tel: 0222-361-1555
Email: cs@misumi.com.vn
8:00 - 17:00 (Mon - Sat)
Search by Category / Brand Tìm theo danh mục, nhãn hiệu
Search by Category Tìm theo danh mục
- inCAD Library Home
- > No.000152 Lifter Mechanism
No.000152 Lifter Mechanism
Lifting mechanism guided by interlocking gears
Relevant category
Miniature Linear Guides
| Product name | Miniature Linear Guides Standard Blocks, Light Preload, Precision Class L Configurable Type |
|---|---|
| Part number | SEB10-55 |
| Features | The most basic type among all the industry standard-compliant blocks. |
* Orange colored cells in the table below indicate the part numbers used in this example.
Selection criteria
Effective when linear motions are needed in limited space
Available sizes
■Miniature Linear Guides (standard blocks, light preloading, slight clearance)
| Material | Hardness |
|---|---|
| Stainless steel | 56HRC～ |
| Carbon steel Carbon Steel (Alloy Steel including SCM) | 58HRC～ |
■Sizes and Dimensions
| Number of Blocks | Block Width | Block Length | Overall Height | Rail Length |
|---|---|---|---|---|
| 1 | 12 | 17.4 | 6 | 25-100 |
| 17 | 23.6 | 8 | 40-130 | |
| 20 | 30 | 10 | 35-275 | |
| 27 | 33.9 | 13 | 45-470 | |
| 32 | 42.4 | 16 | 70-670 | |
| 40 | 50 | 20 | 100-700 | |
| 2 | 12 | 17.4 x 2pcs. | 6 | 70-100 |
| 17 | 23.6 x 2pcs. | 8 | 70-130 | |
| 20 | 30 x 2pcs. | 10 | 75-275 | |
| 27 | 33.9 x 2pcs. | 13 | 95-470 | |
| 32 | 42.4 x 2pcs. | 16 | 110-670 | |
| 40 | 50 x 2pcs. | 20 | 160-700 |
Selection Steps
- Determination on Operating Conditions
- (Moving mass, feed rate, motion pattern, life)
↓
- Temporary selection of linear guide specifications
- (Number of blocks, block type, height and rail length are temporarily selected based on the usage conditions.)
↓
- Basic safety check
-
- Allowable Load
- Operating Life
- Preload
Accuracy Info
■Preload and Accuracy Standards (standard blocks, light preload, slight clearance)
(μm）
| Specification | Light Preload, High Grade | Light Preload, Precision Grade | Slight Clearance, Standard Grade |
|---|---|---|---|
| Radial Clearance | -3-0 | 0～+15 | |
| H Dimension Tolerance | ±20 | ±10 | ±20 |
| Pair variation of H | 15 | 7 | 40 |
| Tolerance of dims. W2 | ±25 | ±15 | ±25 |
| Pair variation of W2 | 20 | 10 | 40 |
■Running Parallelism
(μm）
| Rail length(mm) | ||||||||
|---|---|---|---|---|---|---|---|---|
| -80 | 81-200 | 201-250 | 251-315 | 316-400 | 401-500 | 501-630 | 631-700 | |
| Precision Grade | 2 | 3 | 3.5 | 4 | 5 | 5 | 6 | 6 |
| High Grade | 3 | 7 | 9 | 11 | 11 | 12 | 13.5 | 14 |
| Standard Grade | 13 | 15 | 17 | 18 | 18 | 19 | 21 | 21.5 |
* The slight clearance type has clearances (play) between the rail and blocks.
Performance info.
Rated Load of Linear Guide (wide standard blocks, slight clearance)
| Overall Height | Basic Load Rating | Allowable Static Moment | |||
|---|---|---|---|---|---|
| C (Dynamic) kN | Co (Static) kN | MA N・m | MB N・m | Mc N・m | |
| 6 | 0.3 | 0.6 | 0.8 | 0.8 | 1.5 |
| 8 | 0.9 | 1.5 | 4.1 | 4.1 | 5.2 |
| 10 | 1.5 | 2.5 | 5.1 | 4.1 | 10.2 |
| 13 | 2.2 | 3.3 | 8.8 | 9.5 | 16.1 |
| 16 | 3.6 | 5.4 | 21.6 | 23.4 | 39.6 |
| 20 | 5.2 | 8.5 | 48.4 | 48.4 | 86.4 |
Technical Calculations
Operating Life Calculation for Linear Guides
- Life
- When the linear guide is loaded in linear reciprocating motion, scaly damages called flaking appear due to material fatigue as the stress works on the rolling elements (steel balls) and the rolling contact surfaces (rails) constantly. Total travel distance until the first flaking occurs is called the life of linear guides.
- Rated Life
- Rated life is the total travel distance that 90% of linear guides of the same type can reach, under the same conditions, with no occurrence of flaking damage. Rated life can be calculated with the basic dynamic load rating and the actual load applied on the linear guides, as shown below.
-
- Load must be calculated before actually using linear guides. To obtain loads during linear reciprocating motion, it is necessary to fully consider vibrations and impacts during motion as well as distribution condition of the load applied to linear guides. So, it is not easy to calculation the loads. Operating temperature also critically affects the life. Considering these conditions, the above-mentioned calculation formula will be as follows.
-
- L: Rated Life (Km)
- fH: Hardness Factor (See Fig.1)
- fT: Temperature Factor (See Fig.2)
- fC: Contact Factor (See Table-1)
- fW: Load Factor (See Table-2)
- C: Basic Dynamic Load Rating (N)
- P: Applied Load (N)
- Hardness factor (fH)
-
For liner guide applications, sufficient hardness is required for ball contact shafts. Inappropriate hardness causes less allowable load, resulting in shorter life.
Please correct the rated life with the hardness factor.
- Temperature Factor (fT)
-
When the temperature of linear guides exceeds 100°C, the hardness of guides and shafts will be reduced, and the allowable loads will also be reduced compared to being used at room temperature, causing a reduction of life. Please correct the rated life with the temperature factor.
* Please use Linear Guides at within the heat resistance temperature ranges shown on product pages.
- Contact Factor (fC)
-
Table-1. Contact Factor
Number of Blocks per Rail Contact Factor fC
1 1.00 2 0.81 3 0.72 4 0.66 5 0.61 For actual applications, more than two blocks are generally used per shaft. In this case, the load applied to each block varies depending on machining precision and is not uniformly distributed. As a result, per-block allowable load varies depending on the number of blocks per rail. Please compensate the rated life with contact factors on Table-1.
- Load Factor (fW)
-
Table-2. Load factor
Condition of Use fw No shocks / vibrations, low speed:
15 m/min. or less1.0-1.5 No significant shocks / vibrations,
medium speed: 60 m/min. or less1.5-20 With shocks / vibrations, high
speed: 60 m/min. or more2.0-3.5 To calculate load applied to the Linear Guides, in addition to object weight, it requires inertia force attributed to motion velocity or moment loads. However, it is difficult to calculate the load accurately due to potential vibrations and shocks caused by other element than repeated start-stop motions during reciprocating motion. Thus, Table-2 load factor helps simplify the life calculation.
- Applied Load P Calculation Method
- When moment load is applied to each block, convert the moment load into applied load by the following formula.
-
- P: Applied Load (N)
- F: Downward load (N)
- C0: Static load rating (N)
- MA: Allowable Static Moment - Pitching Direction (N·m)
- MC: Allowable Static Moment - Rolling Direction (N·m)
- Lp: Load Point Distance (m) in Pitching Direction
- Lr: Load Point Distance (m) in Rolling Direction
Spring Plungers
| Product name | Spring Plungers - Stainless Steel |
|---|---|
| Part number | PJXW4-4 |
* Orange colored cells in the table below indicate the part numbers used in this example.
Selection criteria
Effective as space saving and low price components for positioning reaction force
Available sizes
■Spring Plungers - Stainless Steel
| Nose Material | Load Type | Body | Pin | Spring | Operating Temperature | |
|---|---|---|---|---|---|---|
| Material | Material | Hardness | Material | |||
| Stainless Steel | Ultra Light Load | 304 Stainless Steel | 440C Stainless Steel | 55HRC〜 | 631 Stainless Steel | －30〜260℃ |
| Light Load | ||||||
| Heavy Load | ||||||
| Extra Heavy Load | ||||||
| Plastic | Ultra Light Load | Polyacetal | − | －30〜80℃ | ||
| Light Load | ||||||
| Heavy Load | ||||||
| Extra Heavy Load | ||||||
■Sizes and Dimensions
| Screw Dia. (Coarse) | Nose | Body length | |
|---|---|---|---|
| Diameter | Stroke | ||
| M3 | φ1 | 1.5 | 15 |
| 3 | 15 | ||
| M4 | φ1.6 | 2 | 15 |
| 4 | 24 | ||
| M5 | φ2 | 3 | 20 |
| 5 | 27 | ||
| M6 | φ2.5 | 3 | 25 |
| 5 | 30 | ||
| M8 | φ3.1 | 3 | 25 |
| 5 | 27 | ||
| M10 | φ3.8 | 5 | 30 |
| 10 | 43 | ||
| M12 | φ5.5 | 5 | 30 |
| 10 | 43 | ||
| 15 | 51 | ||
| M16 | φ8 | 10 | 57 |
| 15 | 57 | ||
| 20 | 65 | ||
Performance info.
■Spring Load (N) of Spring Plunger (Stainless Steel)
| Load type | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| Screw Dia. (Coarse) | Nose | Ultra Light Load | Light Load | Heavy Load | Extra Heavy Load | |||||
| Diameter | Stroke | min． | max． | min． | max． | min． | max． | min． | max． | |
| M3 | φ1 | 1.5 | 0.1 | 0.4 | 0.4 | 1.3 | 0.8 | 2.9 | 1.1 | 3.4 |
| 3 | 0.1 | 0.4 | 0.2 | 1.3 | 0.6 | 2.9 | 0.8 | 3.4 | ||
| M4 | φ1.6 | 2 | 0.3 | 0.7 | 0.9 | 2.0 | 2.0 | 8.8 | 6.1 | 13.8 |
| 4 | 0.2 | 0.7 | 0.6 | 2.1 | 1.9 | 8.8 | 5.8 | 13.6 | ||
| M5 | φ2 | 3 | 0.4 | 3.0 | 1.4 | 9.7 | 2.7 | 16.3 | 6.8 | 22.0 |
| 5 | 0.4 | 3.0 | 1.1 | 10.3 | 1.0 | 17.1 | 5.7 | 21.5 | ||
| M6 | φ2.5 | 3 | 1.8 | 3.1 | 6.0 | 9.8 | 8.0 | 26.4 | 15.8 | 35.6 |
| 5 | 1.5 | 3.1 | 3.4 | 9.86 | 4.4 | 26.6 | 12.9 | 34.4 | ||
| M8 | φ3.1 | 3 | 1.9 | 3.2 | 6.0 | 9.9 | 14.7 | 27.0 | 21.9 | 36.3 |
| 5 | 1.4 | 3.2 | 4.0 | 9.83 | 6.7 | 26.6 | 14.7 | 34.5 | ||
| M10 | φ3.8 | 5 | 1.6 | 4.6 | 5.7 | 14.7 | 8.2 | 45.7 | 24.5 | 58.6 |
| 10 | 1.6 | 4.6 | 4.4 | 14.7 | 6.2 | 45.1 | 19.8 | 58.7 | ||
| M12 | φ5.5 | 5 | 1.7 | 4.7 | 5.8 | 14.7 | 18.2 | 49.0 | 34.9 | 63.6 |
| 10 | 1.6 | 4.7 | 5.0 | 14.7 | 8.2 | 49.1 | 25.5 | 63.6 | ||
| 15 | 1.8 | 4.7 | 6.9 | 14.7 | 7.5 | 48.9 | 20.1 | 63.7 | ||
| M16 | φ8 | 10 | 2.8 | 10.8 | 9.2 | 34.2 | 18.9 | 68.5 | 38.7 | 88.4 |
| 15 | 2.6 | 10.8 | 8.6 | 34.4 | 14.4 | 68.6 | 33.9 | 88.1 | ||
| 20 | 2.0 | 11.0 | 7.1 | 34.4 | 4.2 | 68.6 | 25.4 | 88.1 | ||
* Min. is the initial load, and max. is the load when the nose is fully compressed.
Adjusting Stopper Screws
| Product name | Adjusting Stopper Screws- Hexagon Socket, L Configurable, Fine Thread |
|---|---|
| Part number | ANBNS4-25 |
* Orange colored cells in the table below indicate the part numbers used in this example.
Selection criteria
Effective in that existing product can be used as the pin for determining the reference position.
Available sizes
■Adjusting Pin (Wit hex socket)
| Adjustment Screw | Material | Hardness | Surface Treatment |
|---|---|---|---|
| Fine Thread | 1045 Carbon Steel | 45-50HRC | Electroless Nickel Plating |
| Trivalent Chromate | |||
| 4137 Alloy Steel | 50HRC- | ||
| 304 Stainless Steel | － | － | |
| 420 Stainless Steel | 45HRC- | － | |
| Coarse Thread | 1045 Carbon Steel | 45-50HRC | Electroless Nickel Plating |
| Trivalent Chromate | |||
| 4137 Alloy Steel | 50HRC- | ||
| 304 Stainless Steel | － | － | |
| 420 Stainless Steel | 45HRC- | － |
| Screw Shaft Dia. (mm) | Length(mm) |
|---|---|
| 3 | 10-40（Increments of 5） |
| 4 | 10-50（Increments of 5）、60 |
| 5 | 10-50（Increments of 5）、60 |
| 6 | 15-50（Increments of 5）、60 |
IDEA NOTE Position setting before insertion of workpiece
Due to the arrangement of the spring plungers and mounting screws at both ends of each liner guide, adjustment of chuck position to center before insertion of workpiece is facilitated.
-
TERMS AND CONDITIONS FOR USE OF CAD DATA-
Your access to the CAD data that MISUMI Corporation (hereinafter referred to as the Company) posts on this site (including 3D CAD data, intermediate 3D CAD data and 2D CAD data; hereinafter referred to as the Data) are of products manufactured and/or sold by the Company (hereinafter referred to as the Products) assumes that you have read and accepted these terms and conditions which govern your use of the Data. If you do not agree to these terms and conditions, you must stop using this website and the Data. You must not use the Data for any unlawful purpose or in any manner inconsistent with these terms and conditions.
- 1. CAD Data
- The Data is prepared for assisting the Company's users in the CAD design process by providing dimensions and other Product information. In order to provide the best speed and stability working within this site, the Product drawings were simplified to reduce the size of the Data. For instance, some of the Products are shown without the oil groove shape, screws or spring shape. Also, please be aware that the tolerance, surface roughness and/or chamfer of the Data may vary from the actual Products.
- 2. Disclaimer on Data
- While the Company has carefully prepared the Data, accuracy of the Data is not guaranteed and is subject to the variances as described above. The Company may also modify, add or delete the Data at any time without prior notice. The Company assumes no liability for any direct, indirect, consequential or special damages that you may claim resulted from your use of the Data or any changes to or deletions of the Data regardless of the reason. The Company provides no warranty as to the quality, accuracy, functionality, safety or reliability of the combination of Products and parts. Example applications and combinations of the Products are provided for illustrative purposes only.
- 3. Copyright
-
Copyrights to the content and the Data belong to the Company or the manufacturers of the Products. The said copyright is protected by the Copyright Act and international treaties. The use (including duplication, modification, uploading, posting, transmission, distribution, licensing, sales and publishing) of the Data except for the purpose to use the Data described above without prior approval of the Company is not allowed. The Data cannot be used for any purposes (including sales promotion) except for designing your machine. If you violate this provision or the laws or regulations, the Company may prohibit you from the use of the Data, the Company’s site and/or take legal action. So long as you comply with these terms and conditions, the Company grants to you a non-exclusive, non-transferable, revocable license to access and use the Data for the sole purpose of assisting you in designing machines that incorporate products.
In case that the CAD data is found to have been to be used for any purpose other than mentioned above or against the related laws, MISUMI may take legal actions, including the one for blocking the involved user from using CAD data and from accessing to the MISUMI site. - 4. Disclaimer of Warranty
- ANY AND ALL CONTENT APPEARING ON THIS WEB SITE IS PROVIDED FOR INFORMATIONAL PURPOSES ONLY. THIS WEB SITE, ITS CONTENT AND ITS LINKS ARE PROVIDED ON AN "AS IS" AND "AS AVAILABLE" BASIS AND ARE USED ONLY AT YOUR SOLE RISK, TO THE FULLEST EXTENT PERMISSIBLE BY LAW. THE COMPANY DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, OF ANY KIND, REGARDING THIS WEB SITE (INCLUDING ITS CONTENT, HARDWARE, SOFTWARE AND LINKS), INCLUDING AS TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, TITLE, NON INFRINGEMENT, RESULTS, ACCURACY, COMPLETENESS, ACCESSIBILITY, COMPATIBILITY, SECURITY AND FREEDOM FROM COMPUTER VIRUS. THE COMPANY WILL NOT BE LIABLE FOR ANY DAMAGES OR LOSSES, INCLUDING DIRECT, INDIRECT, CONSEQUENTIAL, SPECIAL, INCIDENTAL OR PUNITIVE DAMAGES AND/OR LOST PROFITS, IN CONNECTION WITH USE OF THE INTERNET, THIS WEB SITE, ITS CONTENT OR ITS LINKS
Further, the Company will not be liable to you for any failure or delay by the Company to provide access to the Data or any of its obligations under these terms and conditions where such failure or delay is the direct or indirect result of any circumstances beyond the Company's reasonable control (and the Company's obligations will be suspended for the duration of such circumstances).
CAD Download (Unit Assembly)
CAD Download: File Format
CAD Data Limitations
-
Assembly data shows the assembly drawings in the concept design phase. The sole purpose of the data is to explain the structure and functionality of the assembly and is not considered nor to be used as a final design.
You will need to edit the Data so that it meets your specific design conditions. -
Unit assembly Data consists of some sub-assemblies.
It is configured so that each sub-assembly unit can be used as it is or edited. - The Data for fabricated parts is based on easy-to-edit dimensions and shapes in sketches and histories.
- The Data including the third-part components are made by the Company.
* The part in the frame is a sub-assembly unit.
-
Your access to the CAD data that MISUMI Corporation (hereinafter referred to as the Company) posts on this site (including 3D CAD data, intermediate 3D CAD data and 2D CAD data; hereinafter referred to as the Data) are of products manufactured and/or sold by the Company (hereinafter referred to as the Products) assumes that you have read and accepted these terms and conditions which govern your use of the Data. If you do not agree to these terms and conditions, you must stop using this website and the Data. You must not use the Data for any unlawful purpose or in any manner inconsistent with these terms and conditions.
-
- * Unit assembly Data consists of some sub-assemblies.
It is configured so that each sub-assembly unit can be used as it is or edited.
Application Overview
Purpose
- Purpose
- To fit bushings onto a roughly positioned pin.
- Operation
- This mechanism is designed to perform floating in the X and Y directions via two linear guides installed between the lift unit and the bushing chuck. Before the bushing is fit on the pin, the bushing chuck is at the center position. The lift unit lowers the bushing and bushing chuck. The bushing is floated toward the pin and then fit on the pin. After fitting the bushing, the bushing chuck is returned to the center by the spring plunger.
Target workpiece
- (1) Bushing
- Shape: cylinder
- Size: φ20 x H20mm
- Weight: 7g
- (2) Pin
- Shape: column
- Size: φ7 x H15mm
- Weight: 110g
Design Specifications
Operating Conditions or Design Requirements
- Vertical stroke by lift unit: 38mm
- Allowable maximum displacement between inserted workpiece: L = 1.5mm
- Outer dimensions: W88 x D100 x H96mm
Required Performance
- Positioning accuracy: ±0.1mm
Selection Criteria for Main Components
- Spring Plungers
- To enable the bushing chuck to be returned to the center position when the inserted workpiece is unclamped, select spring plungers whose minimum load is larger than the seal resistance of the linear guide, which is between 2N and 5N.
Design Evaluation
Verification of main components
- Compare the centering force against the spring plunger clamp force to see whether the workpiece can be centered
- Check the centering force of the inserted workpiece and the spring plunger clamp power
- Conditional value: centering pin taper angle of inserted workpiece θ = 23°, downward clamp force of lift unit P = 30N, gravitational acceleration g = 9.8m/s², friction coefficient: µ = 0.2 (metal and metal)
- Friction angle: ψ, from μ = tanψ, ψ = tan - 1μ = tan - 1 (0.2) = 11.3°
- The inserting workpiece centering force F is, from P = F x tan (θ + ψ), F = P/(tan (θ + ψ)) = 30/(tan (23 + 11.3)) = 44.0N
- Spring plunger clamp power PS = 5.8 to 13.6N = inserting workpiece centering force F = 44.0N
⇒ As the inserting workpiece centering force is sufficiently larger than the spring plunger clamp power, centering cannot be achieved. The chuck position should be returned to the center before workpiece insertion.
Explore Similar Application Examples
Page
-
/
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Relevant category
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Relevant category
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
