(!)Due to Microsoft's end of support for Internet Explorer 11 on 15/06/2022, this site does not support the recommended environment.
- inCAD Library Home
- > No.000215 Separation Mechanism Utilizing Plate Cams
No.000215 Separation Mechanism Utilizing Plate Cams
Continuous feeding mechanism utilizing plate cams.
Relevant category
Hinge Pin
| Product name | Precision Pivot Pins - Straight, Retaining Rings |
|---|---|
| Part number | CCG6-10 |
* Orange colored cells in the table below indicate the part numbers used in this example.
Selection criteria
A grooved pin is used due to price.
Available sizes
■Precision Pivot Pins - Straight, Retaining Rings
| Material | Hardness | Surface Treatment | Accessory | |
|---|---|---|---|---|
| 1045 Carbon Steel | − | Black Oxide | Retaining Ring 2 pc. | Spring Steel |
| 40 - 45HRC | ||||
| − | Electroless Nickel Plating | 304 Stainless Steel | ||
| 40 - 45HRC | ||||
| Plating hardness 750HV - | Hard Chrome Plating | Spring Steel | ||
| Plating Thickness 3 μm or more | ||||
| 304 Stainless Steel | − | − | 304 Stainless Steel | |
| 440C Stainless Steel | 45 - 50HRC | |||
| 45 - 50HRC Plating hardness 750HV - | Hard Chrome Plating Plating Thickness 3 μm or more | |||
■Sizes and Dimensions
| Pin Dia. | Pin section length （Configurable in 0.1 mm increment） |
|---|---|
| φ2 | 5.0－ 30.0 |
| φ3 | 5.0－ 50.0 |
| φ4 | |
| φ5 | 10.0－ 60.0 |
| φ6 | 10.0－100.0 |
| φ8 | |
| φ10 | 15.0－100.0 |
| φ12 | 15.0－200.0 |
| φ13 | 25.0－200.0 |
| φ14 | |
| φ15 | |
| φ16 | 30.0－200.0 |
| φ17 | |
| φ18 | |
| φ20 | |
| φ22 | |
| φ25 |
Accuracy Info
■Pivot pin Dia. Tolerance (g6) for Hinge Pin Straight Retaining Ring Type
| Pin Dia. | Tolerance |
|---|---|
| φ2・φ3 | -0.002 -0.008 |
| φ4－φ6 | -0.004 -0.012 |
| φ8・φ10 | -0.005 -0.014 |
| φ12－φ18 | -0.006 -0.017 |
| φ20－φ25 | -0.007 -0.020 |
Stainless Steel Deep Groove Bearings
| Product name | Stainless Steel Deep Groove Ball Bearings - V Groove |
|---|---|
| Part number | SZV6-16 |
* Orange colored cells in the table below indicate the part numbers used in this example.
Selection criteria
Suitable for use as a grooved cam follower.
Available sizes
■Stainless Steel Deep Groove Ball Bearings - V Groove
Material: 440C Stainless Steel
■Sizes and Dimensions
(mm)
| Shaft Bore Dia. | O.D. | Thickness |
|---|---|---|
| 3 | 12 | 4 |
| 14 | ||
| 4 | 12 | |
| 14 | ||
| 6 | 16 |
Accuracy Info
■Accuracy of the Stainless Steel Grooved Bearings
Runout Tolerance of V Groove：0.03
Performance info.
■Load Capacity of the Stainless Steel Grooved Bearings
| Shaft Dia. | O.D. | Dynamic Load Rating (N) | Static Load Rating (N) |
|---|---|---|---|
| 3 | 12 | 542 | 186 |
| 14 | |||
| 4 | 12 | ||
| 14 | |||
| 6 | 16 | 235 | 650 |
-
-
Terms of use of CAD data and simplified drawing data- These terms and conditions (hereinafter referred to as “the Terms") set forth the conditions for downloading CAD data and simplified drawing data posted on https://vn.misumi-ec.com/ (hereinafter referred to as the "Website") operated by MISUMI VIETNAM CO.,LTD. (hereinafter referred to as "MISUMI"). By downloading CAD data and simplified drawing data posted on the Website (hereafter referred to as “Data”), customers are deemed to have agreed to these Terms.
- 1. Purpose of Use
-
MISUMI offers the following:
1)CAD data found on the Website (3D CAD data, 3D Intermediate data and 2D CAD data) for the purpose of informing customers of the characteristics of the products offered by MISUMI or a manufacturer affiliated with MISUMI for use in their designs.
2)Simplified drawing data (in PDF format) for the purpose of checking the specifications of products. - 2. Characteristics of Data
- There may be a discrepancy in certain characteristics of products (for example: tolerance, surface roughness, chamfer, etc.) between the Data and the actual product. Furthermore, for the purpose of reducing the file size of the Data, some information such as oil groove shapes, threads, or spring shapes, may be removed from the Data.
- 3. Disclaimer
- MISUMI carefully creates the Data but makes no warranty as to the accuracy of the Data. MISUMI may at any time, and with no prior notice to customers, revise or delete Data. MISUMI assumes no responsibility for any damage or loss resulting from any revision or deletion of the Data, or any errors in said data. Customers are solely responsible for all aspects of their own designs, including those made using MISUMI’s CAD data. MISUMI may provide customers with design example data on the Website, but the quality, accuracy, functionality, safety, reliability, etc., of such data are not guaranteed. MISUMI may, at any time, and in its sole discretion, request that the customer cease its use of or destroy the Data in its possession. MISUMI may request the customer provide MISUMI documentation of such destruction.
- 4.Prohibited Acts
-
Customers or users of the Data, are prohibited from the following acts regarding the Data, in whole or in part:
(1)Requesting quotations or placing orders for products with third parties other than those authorized by MISUMI or its affiliates;
(2)Receiving quotations or orders for products from third parties by providing the Data to a third party or using the Data in their own business;
(3)Displaying links to the Website related to the Data on their own websites, etc., without MISUMI's consent;
(4)Using or reproducing the Data beyond the scope of the above-stated Purpose of Use;
(5)Modifying, altering, tampering with, translating, or adapting the Data;
(6)Selling, transferring, lending, sublicensing, or providing the Data to third parties in any way without MISUMI’s consent;
(7)Altering the content, reverse engineering, decompiling, disassembling, or analyzing the Data;
(8)Publicly disclosing or exhibiting the Data without MISUMI's consent;
(9)Using the Data for the purpose of providing products and services identical or similar to those of MISUMI;
(10)Performing acts that interfere with the proper functioning of this Website, such as acquiring Data in bulk. - 5. Copyright
-
All title and copyright in and to any information contained in the Data are owned by MISUMI or the relevant manufacturer affiliated with MISUMI and are protected by applicable copyright laws and international treaties. By downloading Data, the customer acquires no ownership rights of any kind in the intellectual property contained within. Without prior approval from MISUMI, no part of the Data may be utilized (reproduced, modified, reverse-engineered, uploaded, presented, sent, distributed, licensed, sold, or published) for any purpose other than that mentioned above.
In the event Data is found to have been to be used for any purpose other than that mentioned above or against any applicable laws, MISUMI may pursue any legal remedy available to it, which may result in forbidding the offending user from using the Data or accessing the Website. - 6. Third-Party Data
- MISUMI offers some Data provided by third parties. Such Data may be subject to separate terms and conditions, in addition to these terms. MISUMI makes no guarantee or warranty regarding Data from third parties.
- 7. Export Control
- Customers shall comply with all applicable laws and regulations regarding the export of the Data.
- 8. Amendments to the Terms
- MISUMI may, at any time, and in its sole discretion, modify these terms and conditions; any such modification will be effective immediately.
- 9. Severability
- If any term or provision of these Terms is invalid, illegal, or unenforceable in any jurisdiction, such invalidity, illegality, or unenforceability shall not affect any other term or provision of these Terms or invalidate or render unenforceable such term or provision in any other jurisdiction.
- 10．Miscellaneous
- These Terms and any disputes arising in connection therewith shall be exclusively governed by and construed in accordance with the with the laws of Vietnam without regard to its conflicts of law principles. Any dispute arising out of or in relation with these Terms and Conditions shall be resolved by arbitration at the Vietnam International Arbitration Centre (VIAC) in accordance with its Rules of Arbitration. The place of arbitration shall be Hanoi and the language to be used in the arbitral proceedings shall be English.
- Revised:16th November, 2025
CAD Download (Unit Assembly)
CAD Download: File Format
CAD Data Limitations
-
Assembly data shows the assembly drawings in the concept design phase. The sole purpose of the data is to explain the structure and functionality of the assembly and is not considered nor to be used as a final design.
You will need to edit the Data so that it meets your specific design conditions. -
Unit assembly Data consists of some sub-assemblies.
It is configured so that each sub-assembly unit can be used as it is or edited. - The Data for fabricated parts is based on easy-to-edit dimensions and shapes in sketches and histories.
- The Data including the third-part components are made by the Company.
* The part in the frame is a sub-assembly unit.
-
- * Unit assembly Data consists of some sub-assemblies.
It is configured so that each sub-assembly unit can be used as it is or edited.
Application Overview
Purpose
- Purpose
- Separates workpieces on the feeder.
- Operation
- As a single cylinder operates two sets of plate cams simultaneously, two sets of stoppers alternatively move up and down to separate work pieces.
Points for use
- To maximize efficiency the attachment at the tip of the stopper should be formed according to the work pieces shape.
Target workpiece
- Shape: round connector
- Size: φ30 x 15mm
- Weight: 0.1kg or less
Design Specifications
Operating Conditions or Design Requirements
- Stopper pin stroke：15mm
- Cylinder stroke：50mm
- Outer dimensions：W74xD170xH175mm
Selection Criteria for Main Components
- A compression spring with a loose length of 25mm or longer and a compressed length less than 10mm is selected.
Design Evaluation
Verification of main components
- Selection of a compression spring
- Conditional value: free length of compression spring L1 = 30mm, solid length of compression spring L2=5.6mm
The length (free length) L3 of the spring required in this mechanism is L3＞25mm
And its solid length is L4＜10mm
Therefore,
The selected compression spring satisfies L1 > L3 and L2 < L4
Other Design Consideration
- This mechanism can be manufactured with a set of plate cams and a stopper unit.
- Depending on the mutual design of the two plate cams, it is possible to change the escape timing.
Explore Similar Application Examples
Page
-
/
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Relevant category
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
