(!) Since support from Microsoft will end on January 14th, 2020, Windows 7 will be excluded from the recommended environment from December 15th, 2019 on this site. Vì lý do Microsoft kết thúc hỗ trợ cho Windows 7 vào ngày 14/01/2020, Windows 7 sẽ là hệ điều hành không được khuyến khích sử dụng với trang web này từ ngày 15/12/2019.
Tel: 0222-361-1555
Email: cs@misumi.com.vn
8:00 - 17:00 (Mon - Sat)
Search by Category / Brand Tìm theo danh mục, nhãn hiệu
Search by Category Tìm theo danh mục
- inCAD Library Home
- > No.000173 Angle Adjustment Mechanism
No.000173 Angle Adjustment Mechanism
Simple angle adjustment mechanism for hole inspection.
Relevant category
Hardened Precision Balls
| Product name | Precision Hardened Balls - Inch |
|---|---|
| Part number | BLMJ6 |
* Orange colored cells in the table below indicate the part numbers used in this example.
Selection criteria
Low cost and stocked item, this item is selected as it can be used similarly to a ball joint.
Available sizes
■Precision Hardened Balls - Inch
| Size Increments | Material | Grade | Hardness | Specifications |
|---|---|---|---|---|
| inch | 52100 Bearing Steel | 28 | 61 - 67HRC | JIS B1501 |
| 440C Stainless Steel | 59 - 66HRC | In accordance with JIS-B1501 | ||
| mm | 52100 Bearing Steel | 61 - 67HRC | JIS B1501 | |
| 440C Stainless Steel | 59 - 66HRC | In accordance with JIS-B1501 |
■Sizes
| Size Increments | Diameter | Material | |
|---|---|---|---|
| 52100 Bearing Steel | 440C Stainless Steel | ||
| inch | Sφ1.8 | ○ | ○ |
| Sφ5/32 | ○ | ○ | |
| Sφ3.16 | ○ | ○ | |
| Sφ7/32 | ○ | ○ | |
| Sφ15/64 | ○ | ○ | |
| Sφ1.4 | ○ | ○ | |
| Sφ17/64 | ○ | ○ | |
| Sφ9/32 | ○ | ○ | |
| Sφ5.16 | ○ | ○ | |
| Sφ11/32 | ○ | ○ | |
| Sφ3.8 | ○ | ○ | |
| Sφ13/32 | ○ | ○ | |
| mm | Sφ3 | ○ | ○ |
| Sφ3.5 | ○ | ○ | |
| Sφ4 | ○ | − | |
| Sφ4.5 | ○ | − | |
| Sφ5 | ○ | − | |
| Sφ6 | ○ | − | |
| Sφ8 | ○ | − | |
Accuracy Info
■Class 28 Standards (JIS B1501)
(mm)
| Diameter Deviation | max. | 0.7 |
|---|---|---|
| Sphericity | max. | 0.7 |
| Surface Roughness | max. | 0.05 |
| Diameter Size Variation of the Lot | max. | 1.4 |
Conical Spring Washer
| Product name | Disk Spring Washers |
|---|---|
| Part number | SSRBW4 |
* Orange colored cells in the table below indicate the part numbers used in this example.
Selection criteria
Effectively apply certain tightening torque.
Available sizes
■Disk Spring Washers
| Material | Hardness | Specifications | Applicable Screw DIA. | O.D. | Hole Dia. | Overall thickness | Plate Thickness |
|---|---|---|---|---|---|---|---|
| 304 Stainless Steel | 37 - 46HRC | JIS B1251 Class 2 | M4 | φ7.5 | φ4.3 | 0.7 | 0.45 |
| M5 | φ9 | φ5.3 | 0.85 | 0.55 | |||
| M6 | φ10.5 | φ6.4 | 0.95 | 0.6 | |||
| M8 | φ13.5 | φ8.4 | 1.3 | 0.9 | |||
| M10 | φ16.5 | φ10.5 | 1.6 | 1.1 | |||
| M12 | φ19 | φ13 | 1.75 | 1.2 |
Clamping Screws
| Product name | Clamping Screws- Angle |
|---|---|
| Part number | FSM4-10 |
* Orange colored cells in the table below indicate the part numbers used in this example.
Selection criteria
Clamping screw is selected as it allow plane pressing even when screw axis has angle force applied.
Available sizes
■Clamping Screws- Angle
| Main Body | Ball | |||
|---|---|---|---|---|
| Material | Hardness | Surface Treatment | Material | Hardness |
| 4137 Alloy Steel | 38 - 43HRC | Black Oxide | 52100 Bearing Steel | 55 - 60HRC |
| 304 Stainless Steel | − | − | 440C Stainless Steel | 55HRC - |
■Sizes and Dimensions
| Thread Dia. | Overall Length | Angle Ball | |
|---|---|---|---|
| Diameter | Protrusion | ||
| M4 | 6・10・16 | φ2 | 0.3 |
| M5 | 8・12・20 | φ2.5 | 0.4 |
| M6 | 10・16・20・25 | φ3.2 | 0.5 |
| M8 | 10・12・20・25・30 | φ4.5 | 0.6 |
| M10 | 12・16・20・25・35 | φ6 | 0.6 |
| M12 | 16・20・30・40 | φ7.2 | 0.8 |
| M16 | 20・25・35・50 | φ10.7 | 1 |
Performance info.
■Load Capacity of Clamping Screw (Angle Type)
| Thread Dia. | Withstand Load(kN) |
|---|---|
| M4 | 1.3 |
| M5 | 1.4 |
| M6 | 3.3 |
| M8 | 3.9 |
| M10 | 3.4 |
| M12 | 4.8 |
| M16 | 8.9 |
IDEA NOTE Simple Angle Adjusting Mechanism
Fine angle adjustment is achieved by using steel balls between plates and applying pre-load using adjusting screws and a conical spring.
-
TERMS AND CONDITIONS FOR USE OF CAD DATA-
Your access to the CAD data that MISUMI Corporation (hereinafter referred to as the Company) posts on this site (including 3D CAD data, intermediate 3D CAD data and 2D CAD data; hereinafter referred to as the Data) are of products manufactured and/or sold by the Company (hereinafter referred to as the Products) assumes that you have read and accepted these terms and conditions which govern your use of the Data. If you do not agree to these terms and conditions, you must stop using this website and the Data. You must not use the Data for any unlawful purpose or in any manner inconsistent with these terms and conditions.
- 1. CAD Data
- The Data is prepared for assisting the Company's users in the CAD design process by providing dimensions and other Product information. In order to provide the best speed and stability working within this site, the Product drawings were simplified to reduce the size of the Data. For instance, some of the Products are shown without the oil groove shape, screws or spring shape. Also, please be aware that the tolerance, surface roughness and/or chamfer of the Data may vary from the actual Products.
- 2. Disclaimer on Data
- While the Company has carefully prepared the Data, accuracy of the Data is not guaranteed and is subject to the variances as described above. The Company may also modify, add or delete the Data at any time without prior notice. The Company assumes no liability for any direct, indirect, consequential or special damages that you may claim resulted from your use of the Data or any changes to or deletions of the Data regardless of the reason. The Company provides no warranty as to the quality, accuracy, functionality, safety or reliability of the combination of Products and parts. Example applications and combinations of the Products are provided for illustrative purposes only.
- 3. Copyright
-
Copyrights to the content and the Data belong to the Company or the manufacturers of the Products. The said copyright is protected by the Copyright Act and international treaties. The use (including duplication, modification, uploading, posting, transmission, distribution, licensing, sales and publishing) of the Data except for the purpose to use the Data described above without prior approval of the Company is not allowed. The Data cannot be used for any purposes (including sales promotion) except for designing your machine. If you violate this provision or the laws or regulations, the Company may prohibit you from the use of the Data, the Company’s site and/or take legal action. So long as you comply with these terms and conditions, the Company grants to you a non-exclusive, non-transferable, revocable license to access and use the Data for the sole purpose of assisting you in designing machines that incorporate products.
In case that the CAD data is found to have been to be used for any purpose other than mentioned above or against the related laws, MISUMI may take legal actions, including the one for blocking the involved user from using CAD data and from accessing to the MISUMI site. - 4. Disclaimer of Warranty
- ANY AND ALL CONTENT APPEARING ON THIS WEB SITE IS PROVIDED FOR INFORMATIONAL PURPOSES ONLY. THIS WEB SITE, ITS CONTENT AND ITS LINKS ARE PROVIDED ON AN "AS IS" AND "AS AVAILABLE" BASIS AND ARE USED ONLY AT YOUR SOLE RISK, TO THE FULLEST EXTENT PERMISSIBLE BY LAW. THE COMPANY DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, OF ANY KIND, REGARDING THIS WEB SITE (INCLUDING ITS CONTENT, HARDWARE, SOFTWARE AND LINKS), INCLUDING AS TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, TITLE, NON INFRINGEMENT, RESULTS, ACCURACY, COMPLETENESS, ACCESSIBILITY, COMPATIBILITY, SECURITY AND FREEDOM FROM COMPUTER VIRUS. THE COMPANY WILL NOT BE LIABLE FOR ANY DAMAGES OR LOSSES, INCLUDING DIRECT, INDIRECT, CONSEQUENTIAL, SPECIAL, INCIDENTAL OR PUNITIVE DAMAGES AND/OR LOST PROFITS, IN CONNECTION WITH USE OF THE INTERNET, THIS WEB SITE, ITS CONTENT OR ITS LINKS
Further, the Company will not be liable to you for any failure or delay by the Company to provide access to the Data or any of its obligations under these terms and conditions where such failure or delay is the direct or indirect result of any circumstances beyond the Company's reasonable control (and the Company's obligations will be suspended for the duration of such circumstances).
CAD Download (Unit Assembly)
CAD Download: File Format
CAD Data Limitations
-
Assembly data shows the assembly drawings in the concept design phase. The sole purpose of the data is to explain the structure and functionality of the assembly and is not considered nor to be used as a final design.
You will need to edit the Data so that it meets your specific design conditions. -
Unit assembly Data consists of some sub-assemblies.
It is configured so that each sub-assembly unit can be used as it is or edited. - The Data for fabricated parts is based on easy-to-edit dimensions and shapes in sketches and histories.
- The Data including the third-part components are made by the Company.
* The part in the frame is a sub-assembly unit.
-
Your access to the CAD data that MISUMI Corporation (hereinafter referred to as the Company) posts on this site (including 3D CAD data, intermediate 3D CAD data and 2D CAD data; hereinafter referred to as the Data) are of products manufactured and/or sold by the Company (hereinafter referred to as the Products) assumes that you have read and accepted these terms and conditions which govern your use of the Data. If you do not agree to these terms and conditions, you must stop using this website and the Data. You must not use the Data for any unlawful purpose or in any manner inconsistent with these terms and conditions.
-
- * Unit assembly Data consists of some sub-assemblies.
It is configured so that each sub-assembly unit can be used as it is or edited.
Application Overview
Purpose
- Purpose
- Resin case hole inspection.
- Operation
- Inspect resin case hole using photoelectric sensor. The position of the resin case can be manually adjusted.
Points for use
- Manually adjust angle by loosening and tightening the various screws.
Target workpiece
- Shape: resin case
- Size: W40 x D36 x H60mm
- Weight: 0.09kg
Design Specifications
Operating Conditions or Design Requirements
- Adjustment Range:±4°
- Outer dimensions：W60xD150xH65mm
Required Performance
- Adjusting screw pitch: 0.7mm
Selection Criteria for Main Components
- A steel ball that can secure a clearance of 2mm or longer between plates is selected.
Design Evaluation
Verification of main components
- The steel ball diameter is selected based on the minimum clearance between plates.
- Conditional value: clearance between plates 2mm, intrusion amount 1 x 2 = 2mm,
Distance between contact points of steel ball 2+2=4mm - Steel diameter：4/sin45°=5.67mm
⇒φA diameter of φ = 6mm is selected.
- Conditional value: clearance between plates 2mm, intrusion amount 1 x 2 = 2mm,
Other Design Consideration
- Align Y-axe screws consistently such that the X-axe can be easily adjusted.
Explore Similar Application Examples
Page
-
/
-
-
-
-
-
-
-
-
-
-
-
-
-
Relevant category
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Relevant category
-
-
-
-
-
-
Relevant category
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
