Sprockets Nominal No.60 (C-SPA60B15-N-20)

■ Sprockets is a solid or spoked gear that engages with a roller chain to transfer motion or power.
Application of sprocket: It is widely used in mechanical transmission in chemical industry, textile machinery, food processing, instrumentation,and petroleum

■ Only Sprockets and chains of the same specifications can be used in combination.
This series is ISO 12A/ANSI 60 sprocket, and can be used in combination with MISUMI 60 series chain.
■ Do not use it with ISO/ANSI 16B series chain, which may cause the chain sprocket mechanism to fail to function properly!

■ Due to process reasons, it is impossible to guarantee the coincidence of the tooth tops of multiple Sprockets. If you need to use the tooth tops in an overlapping manner, please contact us.

■ Compared with gear drive and belt drive, Sprockets chain drive has the following characteristics:
1. Multi-tooth load-bearing, safe and reliable;
 2. Flexible transmission, absorbing shock and vibration;
 3. Large center distance range, low manufacturing and installation accuracy requirements;
4. Compared with belt transmission, the transmission ratio is more accurate and the transmission efficiency is higher. It is suitable for the harsh environment of high temperature, dust and humidity.

■ Sprockets, chain selection
Misumi’s sprocket and chain product selection supports the principle of “Nominal Numbering”

Product Drawings of Sprockets (Unit: mm)

 

Sprockets Type	Sprockets Material	Surface Treatment	Accessories
C-SPA60B	Equivalent to S45C (Induction Hardened Teeth Tip)	－	Fixing Screw (Only Shaft Hole Specifications N)

■ Technical information of Sprockets Transmission Mechanism design
■ A single package label may not match the ordered model. It is a factory-managed model. Please note that the outer package label shall prevail!

How to mount the roller Sprockets (A) Axis configuration ■Sprockets Horizontal Even when the two axes are arranged horizontally, the rotation direction of the axis must be considered. The examples (2) and (3) in the figure show that when the Sprockets is stretched, the disengagement between the sprocket teeth and the chain is not smooth and may bite. In particular, the upper and lower chains in (3) will contact each other, so an idler is required.

 

■Sprockets Vertical If the chain is stretched, slack as shown in (5) will occur, and when a small Sprockets is used on the lower side, the chain may fall off. Therefore, please use it at an angle of 60 or less as shown in (4). When it is necessary to use it vertically due to the mechanism or space, it is recommended to put the large sprocket on the lower side, and use the idler on the outside or inside as shown in (6).

 

(B) Deflection Deflection is generally about 4% of the shaft spacing, and about 2% in the following cases. a. The Sprockets Vertical transmission or close to vertical transmission b. Shaft spacing is more than 1m c. When frequent heavy load starting and stopping are required d. When reverse rotation is required

 

(C) When the Sprockets load changes If a tension adjuster is mounted on the tension side or slack side of the Sprockets to provide initial tension in advance, it will eliminate vibration and reduce noise during operation.

■ Sprockets maintenance
1. Sprockets tightness should be suitable. If it is too tight, it will increase power consumption, and bearing is easy to wear; if it is too loose, the sprocket is easy to runout and fall off the chain.
 The degree of tightness of the sprocket is: if lifted up or pressed down from the middle of the sprocket, the center distance between the two sprocket is about 2%-3%.

2. The Sprockets shall be installed on shaft without swing and skew.
 The end faces of the two Sprockets in the same transmission assembly should be in the same plane. When the center distance of the sprocket is less than 0.5 meters, the deviation can be 1 mm.
   When the center distance of the sprocket is more than 0.5 meters, the deviation can be 2 mm. But there shall be no friction on sprocket tooth side. Integral offset.
 If the offset is too large, chain is prone to fall off and wear is likely to accelerate. When replacing the sprocket, you must pay attention to check and adjust the offset

3. After the Sprockets is severely worn, the new sprocket and the new chain should be replaced at the same time to ensure good meshing.
 You cannot replace new Sprockets separately. Otherwise, it will cause bad engagement and accelerate the wear of new Sprockets.
 If the tooth surface of the sprocket is worn to a certain degree, it should be turned over in time (the sprocket used with adjustable surface) to extend the life time.

4. If the new Sprockets is too long or elongated after use, and difficult to adjust, the links can be removed by the case, but the number of the links must be even.
 The link should pass through the back of the sprocket with the lock piece being inserted outside, and the opening of the lock piece should be in the opposite direction of the turning.

5. Lubricating oil should be timely filled when Sprockets are working. Lubricating oil must enter the matching clearance between the roller and the inner sleeve to improve working conditions and reduce wear.

6. The old Sprockets cannot be mixed with some of the new sprocket, and should be replaced as a complete set, otherwise it is easy to produce impact in the transmission. Separate replacement of Sprockets will increase wear.

Please order Sprockets after selecting part number and parameters according to the selection steps to.

Part Number of Sprockets				Shaft Hole Specifications	Shaft Hole Diameter (D)						Dp	D0	H	L	ℓ
Sprockets Type	Sprockets Nominal model	Hub type	Number of Teeth		S Specifications	N Specifications (H7)
C－SPA	60	B	12	S N	14	20		30			73.6	83	51	32	8
			14		16	20	25				85.61	95	62	32
			15		16	20					91.62	101	68	32
			16		16		25				97.65	107	73	32
			23		16					50	139.9	150	83	40	12
			24		18				32		145.95	156
			25		18		25				151.99	162

Fixing Screw of Symbol ＊ is M6.
＊＊ Symbol indicates that there is a notch on the outer diameter of the hub.
■ A single package label of Sprockets may not match the ordered model. It is a factory-managed model. Please note that the outer package label shall prevail!

■ Sprockets, Shaft Hole Machining Size Table

Shaft Hole Diameter D	Keyway b2×t2	Fixing Screw M
19~22	6×2.8	6
24~30	8×3.3	8
32~38	10×3.3	8
40·42	12×3.3	8
45·50	14×3.8	10

Please order sprockets after selecting part number and parameters according to the selection steps to .

Part Number				Shaft Hole Specifications	Shaft Hole Diameter (D)						Dp	D0	H	L	ℓ
Type	Nominal model	Hub type	Number of Teeth		S Specifications	N Specifications (H7)
C－SPA	60	B	12	S N	14	20		30			73.6	83	51	32	8
			14		16	20	25				85.61	95	62	32
			15		16	20					91.62	101	68	32
			16		16		25				97.65	107	73	32
			23		16					50	139.9	150	83	40	12
			24		18				32		145.95	156
			25		18		25				151.99	162

Fixing Screw of Symbol ＊ is M6.
＊＊ Symbol indicates that there is a notch on the outer diameter of the hub.
■ A single package label may not match the ordered model. It is a factory-managed model. Please note that the outer package label shall prevail!

■ Shaft Hole Machining Size Table

Shaft Hole Diameter D	Keyway b2×t2	Fixing Screw M
19~22	6×2.8	6
24~30	8×3.3	8
32~38	10×3.3	8
40·42	12×3.3	8
45·50	14×3.8	10