What is the initial tension?

It can be understood that when a general tensile spring is under tension, the tension measured when it is about to undergo elastic deformation without deformation (critical state) is called the initial tension. It is realized by properly controlling the process parameters in the manufacturing process of tensile spring. MISUMI tension spring specifications (except for free designation) have been standardized, i.e. the maximum load of the same diameter is a certain value. Because the tensile spring is made on the basis of the maximum load, the initial tension and spring coefficient are the reference values.

What is the life of the tensile spring?

Some hook installation methods of tension springs may cause stress concentration, so the standard use times cannot be provided. To increase the use times, it is recommended to use it under 70% of the allowable displacement Fmax. ·It is recommended to use it at room temperature below 40℃ and the load value will decrease due to service conditions at temperature over 40℃.

What is the spring constant?

The spring constant is the force necessary to give the spring unit displacement, which is used to express the characteristics of the spring.

What are the JIS standards for general spring-related materials?

Piano wires: JIS G 3522 Iron wires: JIS G 3532 Hard drawn steel wires: JIS G 3521 Stainless steel wires for springs: JIS G 4313

What is the difference between a piano steel wire spring and a hard drawn steel wire spring?

There is little difference in appearance between the two materials. In short, the piano wire is an advanced material, and the hard drawn steel wire is a general material. The piano wire is often used as a spring for precision machinery while the hard drawn steel wire is mostly used as a peripheral spring for groceries or blinds. They are both high-carbon steels with almost the same chemical composition. The production of piano wires is time-consuming and they are expensive because there is additional standardized management and inspection of impurities, the depth of surface scars, and the depth of decarburized layer. Although the subtle difference is invisible to the naked eye, it has a great influence on the quality of the spring.

(!) Since support from Microsoft will end on January 14th, 2020, Windows 7 will be excluded from the recommended environment from December 15th, 2019 on this site. Vì lý do Microsoft kết thúc hỗ trợ cho Windows 7 vào ngày 14/01/2020, Windows 7 sẽ là hệ điều hành không được khuyến khích sử dụng với trang web này từ ngày 15/12/2019.

Tel: 0222-361-1555 Email: cs@misumi.com.vn 8:00 - 17:00 (Mon - Sat)

ものづくりの、明日を支える。MISUMI-VONA 生産材コマースものづくりの、明日を支える。MISUMI-VONA 生産材コマース

Webcode Seach | Series: #CODE

Keyword suggestionsTừ khóa gợi ý

Part number suggestionsGợi ý mã sản phẩm

Discontinued Products

Search by Category / Brand Tìm theo danh mục, nhãn hiệu

Search by Category Tìm theo danh mục

[Thông báo] Cập nhật địa chỉ kho tập kết hàng hóa tại khu vực miền Nam của MISUMI Việt Nam. Xem chi tiết.
[Announcement] Update on warehouse address in the Southern region of MISUIMI Vietnam. See more. 
[Cảnh Báo] Thủ Đoạn Lừa Đảo Từ Nhân Viên Giao Hàng – Yêu Cầu Trả Phí Ship. Xem chi tiết.
[Warning] Fraud Calling from Shipper - Asking to Pay Shipping Fee. See more.

How can we improve?

How can we improve?

Comments

Name (Optional)

E-mail Address (Optional)

Tel (Optional)

While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
Customer Privacy Policy

Thank you for your cooperation.

While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
Please use the inquiry form.

Customer Privacy Policy

ConfigureTạo

Part number has not been determine

(39 Part Numbers Available)

Configure Remaining SpecificationsĐịnh cấu hình các thông số còn lại

Part Number CompleteĐã hoàn thành

C-WAWT5-15

Allowable Load (Configurable Range) Max. Load Length of Spring Used L+F Free Length L Outer Dia. D Initial Tension Standard Spring Constant Wire Dia. Max. Deflection type CAD Days to Ship

Specification/DimensionsĐặc điểm kỹ thuật / Kích thướcĐặc điểm kỹ thuật / Kích thước

Allowable Load (Configurable Range)(N)
- 15.01~30.00
- 30.01~60.00
- 60.01~110.00
- 110.01~
ClearTrống
Max. Load(N)
20.79

33.15

41.19

77.47

120.62

154.95
ClearTrống
Length of Spring Used L+F(mm)
17.9

23.7

24.6

30.3

31.4

35.2

36.9

37.3

38.4

41.8

43.3

44.1

45

45.8

46.6

48.4

50

51.4

51.9

52

52.7

55

55.8

58.3

58.4

58.6

59.4

61.6

62.5

65.2

65.5

70.9

72.1

75.2

75.6

78.1

78.8

82
ClearTrống
Free Length L(mm)
15

20

25

30

35

40

45

50

60

65
ClearTrống
Outer Dia. D(Ø)
5

6

8

10

12

14
ClearTrống
Initial Tension(N)
5.1

8.6

9.81

20.59

34.3

45.11
ClearTrống
Standard Spring Constant(N/mm)
1.03

1.18

1.38

1.57

1.67

1.86

1.96

2.06

2.27

2.35

2.45

2.65

2.94

3.35

3.43

3.53

3.73

4.31

4.61

4.9

5.39

5.69

5.88

6.57

6.77

7.16

8.34

9.22

10.1

10.89

11.18

13.04

13.14

15.59

19.02
ClearTrống
Wire Dia.(Ø)
0.8

1

1.2

1.6

2

2.3
ClearTrống
Max. Deflection(mm)
2.9

3.7

4.6

5.2

5.3

5.8

6.4

6.6

6.8

6.9

7

7.3

7.7

8.3

8.4

9.1

9.4

10

10.8

10.9

11.4

11.6

11.9

12.1

12.5

13.1

13.3

13.6

15.2

15.5

15.6

17

18.8
ClearTrống
type
- C-WAWT
ClearTrống
CADCAD
- 2D
- 3D
ClearTrống

Days to ShipSố ngày giao hàng

Alltất cả các

Same day
ClearTrống

Specify AlterationsChỉ định thay đổi

Tension Springs Heavy Load, Double Round Hook O.D.5-14

Volume Discount

Check FAQ of this product (5 items)

Brand :

MiSUMi Economy

Part Number :

C-WAWT5-15

C-WAWT5-20

C-WAWT5-25

C-WAWT5-30

C-WAWT5-35

C-WAWT5-40

C-WAWT5-45

C-WAWT5-50

C-WAWT6-20

C-WAWT6-25

C-WAWT6-30

C-WAWT6-35

C-WAWT6-40

C-WAWT6-45

C-WAWT6-50

C-WAWT6-60

C-WAWT8-25

C-WAWT8-30

C-WAWT8-35

C-WAWT8-40

C-WAWT5-15

Order Qty :
Total Price :

---
Days to ship :

---

Select part number to Order Now/ Add to Cart

CAD Download

(i)
Caution

thận trọng

**RoHS Compliant is available for some part numbers.
Please contact with MISUMI for detail effective date.

Product Description

- Tension Springs Heavy Load, Double Round Hook, C-WAWT / C-WAWT series from MISUMI.
- This is an economy item; The price is cheaper than the MISUMI standard product.
- The wire material of spring is made of SWP-A.
- C-WAWT and C-WAWT are Heavy Load Double Hook Tension springs type.
- The outer diameter of spring can be selected from 5.0 mm to 14.0 mm.
- The free length of spring can be selected from 15 mm to 65 mm.

Economy Tension Springs Double Round Hook

Versatile Load RangeHigh-Quality MaterialDurability and Longevity

- These tension springs offer a broad range of allowable loads.

- The springs come with a range of outer diameters and free lengths within specified ranges.

- Available in multiple material options.

- Spring with adjustable tension and constant range

- The double round hook design enhances the spring's attachment security and load distribution, reducing the risk of failure under stress.

Economy Tension Springs Double Round Hook

MISUMI Standard

Cheaper Price

Product Variety

3D CAD
3D CAD Support

Tension Springs Product Overview

◇ Misumi Economy series Tension Springs Heavy Load· Double Hook
◇ Made of quality materials, the Economy series tensile springs have been localized, greatly reducing the cost, and their cost efficiency is higher thanks to Misumi’s higher quality control performance.
◇ Tension Springs, Stainless steel materials are imported from Japan, and anti-rust resistance is high. Stainless steel springs are also magnetic. Please be careful.
◇ Misumi's Economy series tensile springs have been standardized in specifications, that is, the maximum load of the same diameter is a certain value. Initial tension, and the spring coefficient is a reference value.

New Tension Springs Product Heavy Load· Double Hook

Tension Springs Dimensional Drawing

・L = Free length
・D ≤ Ø18mm (±1.0)
・D ≥ Ø18mm (±1.5)

Tension Springs Product Feature

Tension Springs (also known as draw spring) is a spiral spring which bears axial tension. It has side hooks at both ends to ensure the tension source of tension spring.
When not bearing load, the coils of tension spring are generally tight without clearance.
The working principle of Tension Springs is to act in reverse when stretching or pulling away, and to work by using the resilience (pulling force) after stretching, so as to control the movement of machine parts, absorb and store energy, measure the force and so on.

Tension Springs Specifications Overview

The initial tension and the spring constant are reference values, which are different slightly depending on batches. Load {kgf} = Load N×0.101972
Calculation method of laps (reference value):
Total number of laps = (L-2(D-d))/d
Effective laps=total number of laps-2
The number of laps is a reference value, and varies slightly depending on batches.

Tension Springs Precautions

[Tension Springs Precautions for use]
▶ Tension Springs Operating temperature
SWP-A…… Normal temperature (0 to 40℃)
Stainless steel…… -10 to 100℃
※ If the spring is used under conditions exceeding the above temperature, the load value may decrease due to usage conditions.
※ When used in an environment with high and low temperature differences and humidity such as outdoors, it is recommended to choose stainless steel products.

▶ Tension Springs Approximate number of times of use: about 1 million times
※ The above times are for reference only. The number of times of use varies with the tensile direction, operating temperature/environment, and amount of deformation. To increase the usage count, it is recommended to use the spring up to 70% of the allowable displacement Fmax..

▶Others
· Use within the allowable displacement Fmax.(mm). If it is used under the condition of exceeding the allowable displacement, the spring may be deformed, or damaged after using only a limited number of times. Please also be careful not to stretch the tensile spring beyond the allowable displacement when installing it.
· Stainless steel springs are also magnetic. Please be careful.

Tension Springs Example of Use

Tension Springs Example of Use
Installation Diagram

The installation diagram of single hook product is for reference only.

Tension Springs Related Products

(Economy series) Tension Springs, Tensile Spring, Medium and Light Load, Medium Load, Medium and Heavy Load	(Economy series) Tension Springs, Tensile Spring, Ultra Light Load, Light Load	(Economy series) Tension Springs, Tensile Spring, Heavy Load

Tension Springs Specification Table

■ Heavy Load Double Hook Tension Springs Type

Part Number		Wire Diameter dmm	Under dynamic load		(Initial tension) N	(Spring constant) N/mm
Tension Springs Type	D-L	Wire Diameter dmm	Maximum displacement Fmax. Mm	Maximum load N	(Initial tension) N	(Spring constant) N/mm
C-WAWT	5-15	0.8	2.9	20.79	5.1	5.39
	20	0.8	4.6	20.79	5.1	3.43
	25	0.8	6.4	20.79	5.1	2.45
	30	0.8	8.4	20.79	5.1	1.86
	35	0.8	10.0	20.79	5.1	1.57
	40	0.8	11.4	20.79	5.1	1.38
	45	0.8	13.3	20.79	5.1	1.18
	50	0.8	15.2	20.79	5.1	1.03
	6-20	1.0	3.7	33.15	8.6	6.57
	25	1.0	5.3	33.15	8.6	4.61
	30	1.0	6.9	33.15	8.6	3.53
	35	1.0	8.3	33.15	8.6	2.94
	40	1.0	10.0	33.15	8.6	2.45
	45	1.0	10.8	33.15	8.6	2.27
	50	1.0	12.5	33.15	8.6	1.96
	60	1.0	15.6	33.15	8.6	1.57
	8-25	1.2	5.3	41.19	9.81	5.88
	30	1.2	7.3	41.19	9.81	4.31
	35	1.2	9.1	41.19	9.81	3.43
	40	1.2	11.9	41.19	9.81	2.65
	45	1.2	13.6	41.19	9.81	2.35
	50	1.2	15.5	41.19	9.81	2.06
	60	1.2	18.8	41.19	9.81	1.67

Part Number		Wire Diameter dmm	Under dynamic load		(Initial tension) N	(Spring constant) N/mm
Tension Springs Type	D-L	Wire Diameter dmm	Maximum displacement Fmax. Mm	Maximum load N	(Initial tension) N	(Spring constant) N/mm
C-WAWT	10-30	1.6	5.2	77.47	20.59	10.89
	35	1.6	6.8	77.47	20.59	8.34
	40	1.6	8.4	77.47	20.59	6.77
	45	1.6	10.0	77.47	20.59	5.69
	50	1.6	11.6	77.47	20.59	4.9
	60	1.6	15.2	77.47	20.59	3.73
	65	1.6	17.0	77.47	20.59	3.35
	12-40	2.0	6.6	120.62	34.3	13.04
	45	2.0	7.7	120.62	34.3	11.18
	50	2.0	9.4	120.62	34.3	9.22
	60	2.0	12.1	120.62	34.3	7.16
	65	2.0	13.1	120.62	34.3	6.57
	14-40	2.3	5.8	154.95	45.11	19.02
	45	2.3	7.0	154.95	45.11	15.59
	50	2.3	8.4	154.95	45.11	13.14
	60	2.3	10.9	154.95	45.11	10.1

Load {kgf} = Load N×0.101972

Part Number

Incomplete part number.
Please use left hand selections to complete a part number.Incomplete part number.
Please use left hand selections to complete a part number.

Loading...Tải…

: 30; 45; 60

Part Number
C-WAWT5-15
C-WAWT5-20
C-WAWT5-25
C-WAWT5-30
C-WAWT5-35
C-WAWT5-40
C-WAWT5-45
C-WAWT5-50
C-WAWT6-20
C-WAWT6-25
C-WAWT6-30
C-WAWT6-35
C-WAWT6-40
C-WAWT6-45
C-WAWT6-50
C-WAWT6-60
C-WAWT8-25
C-WAWT8-30
C-WAWT8-35
C-WAWT8-40
C-WAWT8-45
C-WAWT8-50
C-WAWT8-60
C-WAWT10-30
C-WAWT10-35
C-WAWT10-40
C-WAWT10-45
C-WAWT10-50
C-WAWT10-60
C-WAWT10-65
C-WAWT12-40
C-WAWT12-45
C-WAWT12-50
C-WAWT12-60
C-WAWT12-65
C-WAWT14-40
C-WAWT14-45
C-WAWT14-50
C-WAWT14-60

Price	Minimum Order Qty.	Volume Discount	Days to ShipSố ngày giao hàng	Allowable Load (Configurable Range) (N)	Max. Load (N)	Length of Spring Used L+F (mm)	Free Length L (mm)	Outer Dia. D (Ø)	Initial Tension (N)	Standard Spring Constant (N/mm)	Wire Dia. (Ø)	Max. Deflection (mm)
3,543 VND	1 Piece(s)	Available	Same day	15.01~30.00	20.79	17.9	15	5	5.1	5.39	0.8	2.9
3,620 VND	1 Piece(s)	Available	Same day	15.01~30.00	20.79	24.6	20	5	5.1	3.43	0.8	4.6
3,620 VND	1 Piece(s)	Available	Same day	15.01~30.00	20.79	31.4	25	5	5.1	2.45	0.8	6.4
3,620 VND	1 Piece(s)	Available	Same day	15.01~30.00	20.79	38.4	30	5	5.1	1.86	0.8	8.4
3,620 VND	1 Piece(s)	Available	Same day	15.01~30.00	20.79	45	35	5	5.1	1.57	0.8	10
3,697 VND	1 Piece(s)	Available	Same day	15.01~30.00	20.79	51.4	40	5	5.1	1.38	0.8	11.4
3,697 VND	1 Piece(s)	Available	Same day	15.01~30.00	20.79	58.3	45	5	5.1	1.18	0.8	13.3
3,772 VND	1 Piece(s)	Available	Same day	15.01~30.00	20.79	65.2	50	5	5.1	1.03	0.8	15.2
3,620 VND	1 Piece(s)	Available	Same day	30.01~60.00	33.15	23.7	20	6	8.6	6.57	1	3.7
3,620 VND	1 Piece(s)	Available	Same day	30.01~60.00	33.15	30.3	25	6	8.6	4.61	1	5.3
3,697 VND	1 Piece(s)	Available	Same day	30.01~60.00	33.15	36.9	30	6	8.6	3.53	1	6.9
3,697 VND	1 Piece(s)	Available	Same day	30.01~60.00	33.15	43.3	35	6	8.6	2.94	1	8.3
3,697 VND	1 Piece(s)	Available	Same day	30.01~60.00	33.15	50	40	6	8.6	2.45	1	10
3,697 VND	1 Piece(s)	Available	Same day	30.01~60.00	33.15	55.8	45	6	8.6	2.27	1	10.8
3,697 VND	1 Piece(s)	Available	Same day	30.01~60.00	33.15	62.5	50	6	8.6	1.96	1	12.5
3,772 VND	1 Piece(s)	Available	Same day	30.01~60.00	33.15	75.6	60	6	8.6	1.57	1	15.6
3,697 VND	1 Piece(s)	Available	Same day	30.01~60.00	41.19	30.3	25	8	9.81	5.88	1.2	5.3
3,697 VND	1 Piece(s)	Available	Same day	30.01~60.00	41.19	37.3	30	8	9.81	4.31	1.2	7.3
3,772 VND	1 Piece(s)	Available	Same day	30.01~60.00	41.19	44.1	35	8	9.81	3.43	1.2	9.1
3,772 VND	1 Piece(s)	Available	Same day	30.01~60.00	41.19	51.9	40	8	9.81	2.65	1.2	11.9
3,929 VND	1 Piece(s)	Available	Same day	30.01~60.00	41.19	58.6	45	8	9.81	2.35	1.2	13.6
3,851 VND	1 Piece(s)	Available	Same day	30.01~60.00	41.19	65.5	50	8	9.81	2.06	1.2	15.5
3,929 VND	1 Piece(s)	Available	Same day	30.01~60.00	41.19	78.8	60	8	9.81	1.67	1.2	18.8
3,772 VND	1 Piece(s)	Available	Same day	60.01~110.00	77.47	35.2	30	10	20.59	10.89	1.6	5.2
3,851 VND	1 Piece(s)	Available	Same day	60.01~110.00	77.47	41.8	35	10	20.59	8.34	1.6	6.8
3,929 VND	1 Piece(s)	Available	Same day	60.01~110.00	77.47	48.4	40	10	20.59	6.77	1.6	8.4
3,929 VND	1 Piece(s)	Available	Same day	60.01~110.00	77.47	55	45	10	20.59	5.69	1.6	10
4,006 VND	1 Piece(s)	Available	Same day	60.01~110.00	77.47	61.6	50	10	20.59	4.9	1.6	11.6
4,239 VND	1 Piece(s)	Available	Same day	60.01~110.00	77.47	75.2	60	10	20.59	3.73	1.6	15.2
4,395 VND	1 Piece(s)	Available	Same day	60.01~110.00	77.47	82	65	10	20.59	3.35	1.6	17
4,318 VND	1 Piece(s)	Available	Same day	110.01~	120.62	46.6	40	12	34.3	13.04	2	6.6
4,860 VND	1 Piece(s)	Available	Same day	110.01~	120.62	52.7	45	12	34.3	11.18	2	7.7
5,014 VND	1 Piece(s)	Available	Same day	110.01~	120.62	59.4	50	12	34.3	9.22	2	9.4
7,701 VND	1 Piece(s)	Available	Same day	110.01~	120.62	72.1	60	12	34.3	7.16	2	12.1
8,079 VND	1 Piece(s)	Available	Same day	110.01~	120.62	78.1	65	12	34.3	6.57	2	13.1
8,461 VND	1 Piece(s)	Available	Same day	110.01~	154.95	45.8	40	14	45.11	19.02	2.3	5.8
8,839 VND	1 Piece(s)	Available	Same day	110.01~	154.95	52	45	14	45.11	15.59	2.3	7
9,220 VND	1 Piece(s)	Available	Same day	110.01~	154.95	58.4	50	14	45.11	13.14	2.3	8.4
9,978 VND	1 Piece(s)	Available	Same day	110.01~	154.95	70.9	60	14	45.11	10.1	2.3	10.9

Loading...Tải…

Basic InformationThông tin cơ bản

Material	SWP-A	Type	Standard Type	Hook Opposing Angle	180° (2 Layers)

The specifications and dimensions of some parts may not be fully covered. For exact details, refer toCác thông số kỹ thuật và kích thước của mã sản phẩm có thể không được bao phủ đầy đủ. Để biết chi tiết chính xác, hãy tham khảo manufacturer catalogsdanh mục nhà sản xuất ..

Frequently asked question (FAQ)FAQ

Question:Question: What is the initial tension?: Answer:Answer: It can be understood that when a general tensile spring is under tension, the tension measured when it is about to undergo elastic deformation without deformation (critical state) is called the initial tension. It is realized by properly controlling the process parameters in the manufacturing process of tensile spring.
MISUMI tension spring specifications (except for free designation) have been standardized, i.e. the maximum load of the same diameter is a certain value. Because the tensile spring is made on the basis of the maximum load, the initial tension and spring coefficient are the reference values.
Question:Question: What is the life of the tensile spring?: Answer:Answer: Some hook installation methods of tension springs may cause stress concentration, so the standard use times cannot be provided. To increase the use times, it is recommended to use it under 70% of the allowable displacement Fmax.
·It is recommended to use it at room temperature below 40℃ and the load value will decrease due to service conditions at temperature over 40℃.
Question:Question: What is the spring constant?: Answer:Answer: The spring constant is the force necessary to give the spring unit displacement, which is used to express the characteristics of the spring.
Question:Question: What are the JIS standards for general spring-related materials?: Answer:Answer: Piano wires: JIS G 3522
Iron wires: JIS G 3532
Hard drawn steel wires: JIS G 3521
Stainless steel wires for springs: JIS G 4313
Question:Question: What is the difference between a piano steel wire spring and a hard drawn steel wire spring?: Answer:Answer: There is little difference in appearance between the two materials. In short, the piano wire is an advanced material, and the hard drawn steel wire is a general material.
The piano wire is often used as a spring for precision machinery while the hard drawn steel wire is mostly used as a peripheral spring for groceries or blinds.
They are both high-carbon steels with almost the same chemical composition. The production of piano wires is time-consuming and they are expensive because there is additional standardized management and inspection of impurities, the depth of surface scars, and the depth of decarburized layer.
Although the subtle difference is invisible to the naked eye, it has a great influence on the quality of the spring.

Check other FAQ (2 items) HideĐóng.

Top of the page

About MISUMIVề Misumi

About this WebsiteVề trang Web này

Useful ToolsCác công cụ hữu ích

Customer ServiceDịch vụ chăm sóc khách hàng

MISUMI Contact Monday to Saturday: 8:00 am - 5:00 pm Order cut off time is 5:00 pm Thứ 2 đến Thứ 7: 8 giờ sáng đến 5 giờ chiều Hạn chót đặt hàng là 5 giờ chiều

Tel:Số điện thoại:0222-361-1555
Fax:Số Fax:0222-361-2555
InquiryYêu cầu

MISUMI APP

Install MISUMI APP

MISUMI Vietnam Company Limited, Legal Representative: Tomohiro Watanabe,
phone: 0222-361-1555, e-mail: cs@misumi.com.vn, Enterprise Code: 0107514576,
Date of Issuance: 22 July 2016, Place of Issuance: Bac Ninh, Business Certificate No. 6573041568-KD dated 27 September 2016 issued by the People's Committee of Bac Ninh

Công ty TNHH MISUMI Việt Nam, Đại diện theo pháp luật: Tomohiro Watanabe,
Điện thoại: 0222-361-1555, e-mail: cs@misumi.com.vn, Mã số doanh nghiệp: 0107514576,
ngày cấp 22/7/2016, nơi cấp: Bắc Ninh, Giấy phép kinh doanh số: 6573041568-KD ngày cấp 27/9/2016 bởi UBND tỉnh Bắc Ninh

Search by Category / Brand Tìm theo danh mục, nhãn hiệu

Search by Category Tìm theo danh mục

How can we improve?

ConfigureTạo

Specification/DimensionsĐặc điểm kỹ thuật / Kích thướcĐặc điểm kỹ thuật / Kích thước

Allowable Load (Configurable Range)(N)

Max. Load(N)

Length of Spring Used L+F(mm)

Free Length L(mm)

Outer Dia. D(Ø)

Initial Tension(N)

Standard Spring Constant(N/mm)

Wire Dia.(Ø)

Max. Deflection(mm)

type

CADCAD

Days to ShipSố ngày giao hàng

Specify AlterationsChỉ định thay đổi

Tension Springs Heavy Load, Double Round Hook O.D.5-14

Copy Part Number URL to Clipboard

(i) Caution thận trọng

Product Description

Economy Tension Springs Double Round Hook

Tension Springs Product Overview

Tension Springs Dimensional Drawing

Tension Springs Product Feature

Tension Springs Specifications Overview

Tension Springs Precautions

Tension Springs Example of Use

Tension Springs Related Products

Tension Springs Specification Table

Part Number

Basic InformationThông tin cơ bản

Frequently asked question (FAQ)FAQ

About MISUMIVề Misumi

About this WebsiteVề trang Web này

Useful ToolsCác công cụ hữu ích

Customer ServiceDịch vụ chăm sóc khách hàng

MISUMI Contact Monday to Saturday: 8:00 am - 5:00 pm Order cut off time is 5:00 pm Thứ 2 đến Thứ 7: 8 giờ sáng đến 5 giờ chiều Hạn chót đặt hàng là 5 giờ chiều

(i)
Caution

thận trọng