Canon Audio Equipment Circular Connector, HA Series
Latch-type round connectors mainly for audio equipment. (Usually known as Cannon connectors.)
[Features]
· There is the HA16 type with its simple and smart streamlined design that puts the cable clamp inside the plug connector, and the HA216 and HA316 types that place the cable clamp on the outside. Select the type that best suits your equipment.
· Due to the shrinking size of devices, there are four different sizes of connector receptacles to suit the area where your device is installed.
· For the three-pin type, there are four interlocking types to choose from.
· There are two types of plug receptacle lock release levers to choose from. The conventional push type, and the more convenient down type (which releases by pushing down on the lever).
· Select your connector depending on usage. The receptacle-side connector comes in either a solder type or a circuit board DIP type.
· In addition, the circuit board DIP type can be mounted inside the device, for even easier ease of connection.
Circular Latch-Lock Type Connectors for Audio Equipment
The series includes 4 types for use in different applications
Specifications of HA Series XLR Connectors
Product Standards
| Rating | Number of Contacts | Rated voltage | Rated Current | Operating Temperature Range | Storage temperature range | |||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 3 | 130 V AC, 180 V DC | 15 A 3 A (board DIP type) | -25 to 70°C | -10 to 60°C | ||||||||
| 4 | 5 A | |||||||||||
| 5 | 4 A | |||||||||||
| Item | Standard | Conditions | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| 1. Contact resistance | 3-contacts, 4-contacts: 5 mΩ or less 3-contacts (board DIP type), 5-contacts: 10 mΩ or less | Measure at 1 A DC | ||||||||
| 2. Insulation resistance: | 1,000 MΩ or more | Measure at 500 V DC | ||||||||
| 3. Withstand voltage | There shall be no flashover or dielectric breakdown | 1,400 V AC for 1 min. | ||||||||
| 4. Vibration resistance | There shall be no electrical discontinuity for 10 μs or greater | Test at 10 to 55 Hz/cycle, Single amplitude: 0.75 mm Three directions, 2 hours each. | ||||||||
| 5. Shock | There shall be no electrical discontinuity for 10 μs or greater | Test at acceleration 490 m/s2, duration: 11 ms, 3 directions, 3 times each. | ||||||||
| 6. Mating cycle | 3-contacts, 4-contacts: 10 mΩ or less 3-contacts (board DIP type), 5-contacts: 20 mΩ or less | 1,000 times | ||||||||
| 7. Temperature cycle | Insulation resistance 1,000 MΩ or more | Leave at -55°C: 30 mins. > Room temperature: 10 to 15 mins. > 85°C: 30 mins.> Room temperature: 10 to 15 mins. for a total of 5 cycles. | ||||||||
| 8. Humidity resistance | Insulation resistance: 10 MΩ or more (at high humidity) 100 MΩ or more (when dry) | Temperature: 40°C, relative humidity: 90 to 95%, left for 96 hours. | ||||||||
Materials
| Parts | Materials | Finish | Note | |||||||
|---|---|---|---|---|---|---|---|---|---|---|
| Exterior | Aluminum alloy or zinc alloy | Matte-finished nickel plating | ― | |||||||
| Insulator | Polyamide resin or PBT resin | ― | UL94V-0 | |||||||
| Contacts | Copper alloy | Silver plating | ― | |||||||
List of Products In This Series
Plug
Plug
Example: HA16PA-3S(71)
Plug
Example: HA216P-4S(71)
Jack
Jack
Example: HA16JA-3P(76)
Jack
Example: HA216J-4P(76)
Receptacle (Solder Type)
Large flange type
Example: HA16R-3P(76)
Medium flange type
Example: HA16RD-3P(76)
Small flange type
Example: HA16RA-3P(76)
Inside mount Type
Example: HA16RM-3P(76)
Receptacle (Board DIP Type)
Receptacle
(inside mount type, straight DIP type)
HA16RM-3PE(76)
Receptacle
(inside mount type, right-angle DIP)
HA16RM-3PB(76)
Plug Receptacle (Solder Type)
Plug receptacle
(small flange type)
HA16PRH-3S
HA16PRK-4S
Plug receptacle
(inside mount type)
HA16PRM-3S(05)
Plug Receptacle (Board DIP Type)
Plug receptacle
(inside mount type, straight DIP type)
HA16PRM-3SE(71)
Plug receptacle
(inside mount type, right-angle DIP)
HA16PRM-3SB(71)
Gang Type
Gang type
(plug-receptacle solder type)
HA16PRN-3SF-A(71)
Gang type
(plug-receptacle board PCB through-hole type)
HA16PRN-3SE-A(71)
Product Usage Precautions
Usage Precautions for Receptacle Side
If heat shrink tubing is applied to the solder terminating section for insulation purposes, overheating could reduce the torque of the screw tightness.
Such overheating may result in loosening and possible loss of the screw. Be sure to confirm that a minimum torque of at least 0.1 N·m is obtained after termination.
If a torque of at least 0.1 N·m cannot be achieved, the screw should be tightened to between 0.3 and 0.4 N·m.